Page 1
Page 2
Page 3
Page 4
Page 5
Page 6
Page 7
Page 8
Page 9
Page 10
Page 11
Page 12
Page 13
Page 14
Page 15
Page 16
Page 17
Page 18
Page 19
Page 20
Page 21
Page 22
Page 23
Page 24
Page 25
Page 26
Page 27
Page 28
Page 29
Page 30
Page 31
Page 32
Page 33
Page 34
Page 35
Page 36
Page 37
Page 38
26 I WWW.CONCO.NET Designed to solve the most difficult deposit problems Conco HydroDrills combine powerful rotary tube cleaning action with a 7.6 to 11.4 LPM 2 to 3 GPM water flush to clear even completely blocked tubes.They are ideal for cleaning all types of heat exchangers including chillers oil coolers condensers and process manufacturing tubes. Conco offers two versions of the HydroDrill the Dominator and the Mitee Mouse II.The Dominator is our large heavy-duty unit. It is powered by compressed air and a booster pump delivering 17.2 BAR 250 PSI at a minimum of 70 LPM 20 GPM 121 LPM 32 GPM recommended and is designed to clean tubes from 13 mm to 70 mm 12 to 234 O.D.The Mitee Mouse II is a hand held unit powered by compressed air and water and is designed to clean tubes from 13 mm to 70 mm 12 to 234 O.D. Both the Dominator and the Mitee Mouse II are easy to set up and operate. HydroDrill tube cleaning is fast and efficient. A 6 m 20 long tube can be cleared of hard deposits in only 30 to 90 seconds. A heavily fouled or even a completely blocked tube can be easily restored to its original I.D. in a single pass. Cleaning with HydroDrill brushes can restore a tubes interior to as-new condition. HydroDrills are used to remove hard tough deposits including n Coke n Calcium n Sulfur n Bauxite TUBE CLEANING SYSTEMS Got scale No Problem.These rotary tube cleaners will even clear tubes plugged solid with hard deposits. n Alumina n Asphalt n Oxides n Polymers HowTheyWork A HydroDrill uses a brush or drill bit mounted to the tip of a rotating Kelly Rod or Extension Rod and a water flush to remove debris. As the rod rotates the unit pumps water through the rod to weep holes in the cleaning tool flushing away hardened deposits as they are loosened. Safe OnTubes The HydroDrill system is designed for maximum cleaning effectiveness with no tube damage. Drill bits are sized to be 0.127 mm 0.005 below the minimum tube I.D. They feature long shanks to ensure that the axis of the bit and the axis of the tube are in complete alignment. Furthermore the bits are designed with carbide tips on the leading edge only and rounded corners to ensure no sharp edges directly impact the tube wall. The drill also rides on a thin layer of water for lubricating bearing surfaces between the bit and the tube. HydroDrills have been used repeatedly to clean process fouling on some heat exchangers over 1000 times with no tube damage or degradation Features n Air and water powered no electricity required n Heavy-duty construction n Custom length Kelly Rods Dominator and sectional Extension Rod design Mitee Mouse II for extending shaft length n Interchangeable brushes and drill bits n Air and water hose available in 7.5 m 25 and 15 m 50 lengths n Hand lever activation Specifications Motor Power 0.7 kW 1 HP Air Requirements Minimum 5.5 BAR at 112 CMH 80 PSI at 125 CFM Water Requirements Minimum 17.2 BAR at 76 LPM 250 PSI at 20 GPM Water Flush at DrillTip 7.6 to 11.4 LPM 2 to 3 GPM Flexible Shaft Speed 1200 RPM Free Spinning 2400 RPM Air andWater Hose 19 mm 34 with Chicago quick connect fittings Packaged and Ready for Shipment Crate Dimensions 60 cm 24 high x 60 cm 24 wide x drill length 0.6 m 2 deep CrateWeight 544 kg 1200 lbs net dry Note Front and rear stand required for horizontal operation. Note A 3.7 kW 5 HP Terminator option is available for the toughest deposits on tubes larger than 29mm 118 O.D. only. All components are the same with the exception of the 3.7 kW 5 HP Terminator drive. Note Pumping system not included call for pump options. Note See page 27 for Kelly Rods brushes and drill bits. Specifications Motor Power 0.6 KW 0.8 HP Air Requirements Minimum 6.2 BAR at 37.4 CMH 90 PSI at 22 CFM Water Requirements Minimum 1.7 BAR at 76 LPM 25 PSI at 20 GPM Water Flush at DrillTip 7.6 to 11.4 LPM 2 to 3 GPM Flexible Shaft Speed 5000 RPM Free Spinning 6000 RPM Air andWater Hose 19 mm 34 with Chicago quick connect fittings Dimensions 28 cm 11 high x 18 cm 7 wide x 36 cm 14 deep Weight 4.5 kg 10 lbs net dry Note See page 27 for Extension Rods brushes and drill bits. Mitee Mouse II HydroDrillTube Cleaning System Dominator HydroDrillTube Cleaning System GLDR-DOM Dominator HydroDrill Tube Cleaning System including barrel assembly complete with dual or single motor drive and one Kelly Rod support mast complete with adjustable A-arms filter lubricator assembly and foot pedal assembly Call for Customization Options and Prices GLMM Mitee Mouse II HydroDrillTube Cleaning System including hand held drill unit with drive cone and rod eight 0.9 m 3 Extension Rods eight sub connectors two sub adaptors 19 mm x 2 m 34 x 7 air hose with oiler and tool box Call for Customization Options and Prices